1800-PH-SIDE-FIN-WHT

| /

Pau Hana side bites for certain boards like Big EZ Hawaiian, Carve, Oahu, Moon Mist, and Angler. See board details and diagrams for further instruction on how to properly install the side bites or to see if they are even compatible with your board at all. These side bites are used for surfing to enhance the boards carving ability.

FEATURES:

  • This is a set of custom Pau Hana Surf Supply Side Bite Fin
  • Comes with two side bite fins and a fin key

* Compatible on the forward side Fin Boxes only.

*Not compatible with the rear side Fin Boxes on the Oahu and Carve.


Questions & Answers

Have a Question?

Be the first to ask a question about this.

Ask a Question

SHOP RELATED PRODUCTS


ACCESSORY FAQS

Alabama | 7-9 days
Alaska | 6-8 days
Arizona | 5-7 days
Arkansas | 7-9 days
California | 5-7 days
Colorado | 6-8 days
Connecticut | 8-11 days
Delaware | 7-9 days
Florida | 7-9 days
Georgia | 7-9 days
Hawaii | 6-8 days
Idaho | 6-8 days
Illinois | 7-9 days
Indiana | 7-9 days
Iowa | 7-9 days
Kansas | 7-9 days
Kentucky | 7-9 days

Louisiana | 7-9 days
Maine | 8-11 days
Maryland | 7-9 days
Massachusetts | 8-11 days
Michigan | 8-11 days
Minnesota | 8-11 days
Mississippi | 7-9 days
Missouri | 7-9 days
Montana | 7-9 days
Nebraska | 7-9 days
Nevada | 5-7 days
New Hampshire | 8-11 days
New Jersey | 7-9 days
New Mexico | 6-8 days
New York | 8-11 days
North Carolina | 8-11 days
North Dakota | 8-11 days

Ohio | 7-9 days
Oklahoma | 6-8 days
Oregon | 6-8 days
Pennsylvania | 7-9 days
Rhode Island | 8-11 days
South Carolina | 8-11 days
South Dakota | 7-9 days
Tennessee | 7-9 days
Texas | 7-9 days
Utah | 5-7 days
Vermont | 8-11 days
Virginia | 8-11 days
Washington | 6-8 days
West Virginia | 8-11 days
Wisconsin | 7-9 days
Wyoming | 6-8 days

Please note all days are in business days from the day after that the order is received by Pau Hana.

To keep your D-Rings and other accessories in good condition, see tips below!

1. Lightly coat any accessory that is being screwed into the SeaMount® with a lightweight oil like WD-40 on the threads. This will prevent galvanic corrosion between dissimilar metals. This is especially important if you are planning on leaving accessories in your board for an extended period of time.

2. It is recommended to remove any accessory and fin hardware often and apply a light coat of oil like WD-40 on them again to make sure that the threads are lubricated. Rine the board, SeaMounts® with freshwater after every use especially after use in salt water.

3. Every metal part on accessories will eventually rust, but by oiling them this should greatly extend the life of the products along with the SeaMounts® themselves.

4. The stainless steel that we use in the SeaMount® is SUS304. What this means is that everything that is screwed into it should theoretically be that grade. Galvanic corrosion shouldn't be happening between different grades of stainless steel, but it is possible. So, if you want to buy a new screw for D-Rings, be sure to know the right grade of stainless steel to get.

5. Better yet, get your accessories from Pau Hana because we use similar metals in all accessories.

 

share the stoke!

#PAUHANASURFSUPPLY